The idea behind these instructions is to give you a guideline for amount of usage to match your body's amount of resultant cleansing so that you don't try to do too much too soon and get sick from excess cleansing. The immune system & liver & kidneys will cleanse the blood of deactivated viruses/bacteria/yeast but only at a rate that is unique to you. Therefore you should start out slowly and every week increase usage time if you feel up to it. If you have a Magnetic Pulser then use it first and don't start using the Microbe Electrifier till you stop getting major cleansing (lymph draining) reactions from the Pulser.
Simple Microbe Electrifier usage
It normally takes people 6-8 weeks to complete microbe electrification treatment although circulation impaired people and people with CFIDS, AIDS, and other immune dysfunction diseases often have to progress (increment the usage time weekly) more slowly which extends the total treatment period. Precautions: There are none because the 10 hertz output frequency does not cause electroporation/transfection.
Protocol: Start by using the Microbe Electrifier for 15 minutes. If the next day you don't feel very toxic (with headaches, tiredness, achiness, etc) then increase your usage time by 5 minutes. But if you get excess cleansing reactions then lessen the treatment time to 5-10 minutes. To aid the body expel the trash from the bloodstream you can drink a lot of water or celery juice and take as a diuretic parsley tea, watermelon, or cucumber. Your cleansing reactions determine the pace you need. It's normal to be able to increase your usage time once a week (if you're not having excessive cleansing reactions). Don't go so fast that you overly sicken yourself with excess cleansing reactions. If you don't start out slow the first 2 weeks then you may overly lower your immune system (from white blood cell lysing) so that you could get sick from some infection. Do enough time so that you feel cleansing reactions but don't overdo it. If you have an almost non-functioning immune system and don't experience any cleansing reactions then take an herbal immune booster such as Beta Glucan from www.nsc24.com to increase your immunity. Also make sure there are no dental infections because those bacteria and their waste are very damaging to the immune system. (read more) If you've used the device for 2 months and you are still getting cleansing reactions from it then you should continue using it daily until you no longer get those reactions and then for one more week for 2-3 hours daily (1 in the morning and 1-2 at night). Make sure the Microbe Electrifier is used every day without skipping any. AIDS patients need to use it the same time every day (+/- 2hrs) because HIV has a 1.2 day life cycle. For viral infections, if you skip a day then you'll have to continue using it for at least 21 days from that skipped day because of the 21 day life cycle of most viruses. Don't skip a day!
Positive Thinking: It may be helpful if you encouraged yourself daily to resist the tendency to become skeptical and give up. Do this by thinking positive thoughts about the new life you'll have once you've regained your health. It will be definitely worth any trouble encountered. Life can be so sweet when vitality brightens every moment of your existence.
Simple Microbe Electrifier Instructions
Proper operation and strength of batteries are good when you are able to adjust the current high enough to cause the red light to fully come on. To replace the batteries just use a Phillips screwdriver to unscrew the cases bottom 4 screws, pull off the cover, and then pull off the snap clips from each battery so that they can be replaced with new alkaline ones.
Choosing electrode site: Both electrodes on the inside of one wrist is the easiest site for convenient usage, but it affects the least amount of blood and the current has to be turned up to a painful level for enough to flow in the arteries since most of it will just cross over through the muscles. Beck proved that 3mA of current is necessary with this arrangement but no one except for nerve-damaged people can tolerate that high level. Using one electrode on one wrist and the second one on the other wrist is my favorite because plenty of blood is affected. This method causes people to worry about current affecting the heart but the current doesn't go thru it. [drawing] Using the electrodes on both ankles affects the most amount of blood, but will barely allow enough electrical current for some people (due to mineral deficiencies) and is hardest for initiating and maintaining correct electrode placement.
Locating electrode placement sites for both wrists: The locations are the inner side of the wrists about 1+1/2 inches below the wrist crease to the outside of the main tendon on the little finger side or thumb side. Each wrist should have one electrode held in place by one wrist band. (picture) This is the most preferred electrode placement. Below is a video showing how to wet the electrodes, connect them to your wrists, and then how to turn up the current dial till the red light is fully on.
Locating electrode placement sites for ankles: On the inner side of each foot locate the pulse of the unseen artery between the ankle and the heel. If you can't feel it then go for a brisk walk for ten minutes and then feel for it without elevating your foot. On top of these pulsating arteries are the sites. (picture)
Connecting Electrodes: Clean & dry the electrode sites. Soak each of the cloth electrodes thoroughly with tap water (not distilled). Squeeze the middle of the insulation of the Microbe Electrifier's alligator clips (at the end of its wires) so that you open the jaws and then let them bite onto the electrodes ends. (picture) Place the electrode over the artery. Then put the elastic band around it and the wrist. Don't pull it tight. Just enough stretch to keep it in place is good. If using electrodes on the ankles, then attach them there with 1" wide medical tape. Re-wet the cloth electrode after 1 hour of use.
Making Saltwater: If your tap water isn't very electrically conductive then you can make some saltwater by putting a couple of shakes of salt from the saltshaker into a cup of purified water and stirring it. This is very electrically conductive but also very corrosive to the alligator clips.
Using the device: Connect the wet electrodes to you. Turn the current control dial fully counter-clockwise and flip the switch to the ON position. Turn the current dial clockwise until the current light comes on fully. The current light will indicate when you are getting 140ua through your bloodstream. If it won't light at maximum dial position then one of 5 conditions exist; 1) Your body's salt & mineral level is very low, 2) Where you placed the electrodes is unsuitable, 3) You need to use saltwater on the electrodes instead of tap water, (4) the batteries need to be replaced, (5) your body is dehydrated. If your body's salt level is low then start salting your food withsea salt (which doesn't cause high blood pressure). If you still can't get the light to come on fully then you need to return the unit and buy the higher powered Microbe Electrifier Plus. If the electrodes 'sting' or 'bite' then 1) the current dial setting is too high, 2) your skin is dirty, 3) you need to relocate the electrodes.
Comfort Suggestions: If the elastic strap is too tight it will leave ridges on the skin when taken off. You can also sew something soft onto the inside of the band (if a natural fiber then not where the electrodes will be because natural fibers will wick away the electrodes moisture). If your skin becomes irritated where the electrodes touch then maybe you're applying too much current or you should place the electrodes on the ankles instead of the wrists.
Making Wrist Electrodes: Any thick 100% cotton cloth can be used to make your own electrodes. The dye in the cloth can be purged out by soaking the cloth in 2/3 bleach and 1/3 water overnight. Here's a drawing showing how to make the electrodes:
